ET 200SP, arrancador directo F 0,9-3A HF
Siemens

ET 200SP, arrancador directo F 0,9-3A HF

Arrancador directo de seguridad High Feature; maniobra electrónica; protección electrónica contra sobrecarga hasta 1,1 kW/400 V; rango de ajuste 0,9...3 A; PROFIenergy; opción: módulo 3DI/LC

  • ComunicaciónYes
Protección y seguridad
intrinsic device protectionYes
for power supply reverse polarity protectionYes
product function short circuit protectionYes
design of short-circuit protectionfuse
performance level (PL) according to ISO 13849-1PL e
category according to ISO 13849-14
device type according to ISO 13849-11
Safety Integrity Level (SIL) according to IEC 61508SIL 3
safety device type according to IEC 61508-2Type B
PFH according to IEC 61508 relating to SIL6E-9 1/h; for switching frequency 30/h
PFDavg with low demand rate according to IEC 615089E-7; for switching frequency 30/h
hardware fault tolerance according to IEC 615081
touch protection against electrical shockfinger-safe
protection class IP on the front according to IEC 60529IP20
touch protection on the front according to IEC 60529finger-safe
Safety Integrity Level (SIL) according to IEC 61508 relatingSIL 1
hardware fault tolerance according to IEC 61508 relating to1
type of the motor protectionsolid-state
Datos eléctricos
insulation voltage rated value500 V
overvoltage categoryIII
surge voltage resistance rated value6 kV
consumed current maximum140 mA
number of poles for main current circuit3
adjustable current response value current of the current0.9 ... 3 A
operating voltage rated value48 ... 500 V
relative symmetrical tolerance of the operating voltage10 %
operational current at AC at 400 V rated value3A
operating power for 3-phase motors at 400 V at 50 Hz0.37 ... 1.1 kW
input voltage at digital input at DC rated value24 V
input current at digital input for signal <1> typical0A
type of voltage of the supply voltageDC
supply voltage at DC rated value24 V
inrush current peak at 24 V25 A; Observe the manual for group configuration
duration of inrush current peak at 24 V0.14 ms
when switched off via supply voltage maximum120 ms
for supply voltage line-sidePlug contact to Base Unit
full-load current (FLA) for 3-phase AC motor at 480 V rated3A
current with locked rotor (LRA) for 3-phase AC motor at 480 V24 A
operating voltage at AC at 60 Hz according to CSA and UL480 V
Entradas/Salidas y comunicación
PROFIBUS DP protocolYes
PROFINET protocolYes
type of electrical connection of the communication interfacePlug contact to Base Unit
Condiciones ambientales
installation altitude at height above sea level maximum4 000 m
Prestaciones y durabilidad
B10 value with high demand rate according to SN 319201 000 000
Otras características
product brand nameSIMATIC
product categoryMotor starter
product type designationET 200SP
equipment version according to IEC 60947-4-23
product functionFail-safe direct-on-line starter
on-site operationYes
remote firmware updateYes
degree of pollution2
between main and auxiliary circuit500 V
shock resistance6 g / 11 ms
vibration resistance15 mm to 6 Hz; 2 g to 500 Hz
operating frequency maximum1 1/s
type of coordination1
according to IEC 60947-4-2AC-53a: 3 A: (8-0,7: 70-32)
Net Weight0.427 kg
direct startYes
EMC emitted interference according to IEC 60947-1class A
EMC immunity according to IEC 60947-1Class A
due to burst according to IEC 61000-4-43 kV
due to conductor-earth surge according to IEC 61000-4-54 kV
due to conductor-conductor surge according to IEC2 kV
due to high-frequency radiation according to IEC 61000Class A
field-based interference according to IEC 61000-4-320 V/m
electrostatic discharge according to IEC 61000-4-28 kV air discharge
conducted HF interference emissions according toClass A for industrial environment
product function suitable for safety functionYes
safety-related switching OFFYes
safe stateLoad circuit open
test wear-related service life necessaryYes
function test interval maximum0.083 a
stop category according to IEC 60204-10
proportion of dangerous failures with high demand rate50 %
Safety Integrity Level (SIL) according to IEC 62061SIL 3
Safe failure fraction (SFF)99.5 %
design of the switching contactHybrid
minimum load [%]50 %; from smallest adjustable rated current
operating frequency 1 rated value50 Hz
operating frequency 2 rated value60 Hz
relative positive tolerance of the operating frequency5%
relative negative tolerance of the operating frequency5%
ampacity when starting maximum30 A
number of digital inputs5
note4 via 3DI/LC module
safety-related1
type of input characteristicType 1 in accordance with EN 61131-2
minimum permissible20.4 V
maximum permissible28.8 V
ON-delay time35 ms
OFF-delay time35 ... 50 ms
when switched off via control inputs maximum55 ms
mounting positionVertical, horizontal (observe derating)
fastening methodpluggable in BaseUnit
height142 mm
width30 mm
depth150 mm
upwards50 mm
downwards50 mm
60721not get into the devices)
relative humidity during operation10 ... 95 %
air pressure according to SN 31205900 ... 1 060 hPa
product function bus communicationYes
supports PROFIenergy measured valuesYes
supports PROFIenergy shutdownYes
1 for digital input signalsPluggable module - accessory
2 for digital input signalsPlug contact to Base Unit
for main energy infeedPlug contact to Base Unit
for load-side outgoing feederPlug contact to Base Unit
wire length for motor unshielded maximum200 m
tificateates/Test Report
Dangerous goodsEnvironment
last modified:4/30/2026

Ficha técnica oficial del fabricante con todas las especificaciones.

Producto bajo pedido

Puedes pedirlo ya: te lo servimos en el plazo indicado. Selecciona la cantidad para añadirlo al carrito.

Plazo de entrega (días):
Avísame cuando haya stock

Si prefieres esperar a que vuelva a haber envío inmediato, déjanos tu email.

Solo usaremos tu email para avisarte de este artículo.

Avísame cuando esté disponible

ET 200SP, arrancador directo F 0,9-3A HF
€539,93 EUR
3RK1308-0CC00-0CP0
Plazo de entrega (días):
€539,93 EUR /cada
Total:

Accesorios