ET 200SP, arrancador inversor 4,0-12A HF

DescripciónEspecificacionesDescargasStock

Arrancador inversor High Feature; incl. ventilador (3RW4928-8VB00); maniobra electrónica; protección electrónica contra sobrecarga hasta 5,5 kW/400 V; rango de ajuste 4,0...12 A; PROFIenergy; opción: módulo 3DI/LC

ComunicaciónYes

Protección y seguridad

intrinsic device protection	Yes
for power supply reverse polarity protection	Yes
product function short circuit protection	Yes
design of short-circuit protection	fuse
touch protection against electrical shock	finger-safe
protection class IP on the front according to IEC 60529	IP20
touch protection on the front according to IEC 60529	finger-safe
type of the motor protection	solid-state

Datos eléctricos

insulation voltage rated value	500 V
overvoltage category	III
surge voltage resistance rated value	6 kV
consumed current maximum	180 mA
number of poles for main current circuit	3
adjustable current response value current of the current	4 ... 12 A
operating voltage rated value	48 ... 500 V
relative symmetrical tolerance of the operating voltage	10 %
operational current at AC at 400 V rated value	12 A
operating power for 3-phase motors at 400 V at 50 Hz	2.2 ... 5.5 kW
type of voltage of the supply voltage	DC
supply voltage at DC rated value	24 V
inrush current peak at 24 V	25 A; Observe the manual for group configuration
duration of inrush current peak at 24 V	0.14 ms
for supply voltage line-side	Plug contact to Base Unit
full-load current (FLA) for 3-phase AC motor at 480 V rated	12 A
current with locked rotor (LRA) for 3-phase AC motor at 480 V	72 A
operating voltage at AC at 60 Hz according to CSA and UL	480 V

Entradas/Salidas y comunicación

PROFIBUS DP protocol	Yes
PROFINET protocol	Yes
type of electrical connection of the communication interface	Plug contact to Base Unit

Condiciones ambientales

installation altitude at height above sea level maximum	4 000 m

Prestaciones y durabilidad

MTBF	46 a

Otras características

product brand name	SIMATIC
product category	Motor starter
product type designation	ET 200SP
equipment version according to IEC 60947-4-2	3
product function	Reversing starter
on-site operation	Yes
remote firmware update	Yes
degree of pollution	2
between main and auxiliary circuit	500 V
shock resistance	6 g / 11 ms
vibration resistance	15 mm to 6 Hz; 2 g to 500 Hz
operating frequency maximum	1 1/s
type of coordination	1
according to IEC 60947-4-2	AC-53a: 12 A: (8-0,5: 72-32)
Net Weight	0.46 kg
direct start	Yes
reverse starting	Yes
EMC emitted interference according to IEC 60947-1	class A
EMC immunity according to IEC 60947-1	Class A
due to burst according to IEC 61000-4-4	2 kV
due to conductor-earth surge according to IEC 61000-4-5	2 kV
due to conductor-conductor surge according to IEC	1 kV
due to high-frequency radiation according to IEC 61000	Class A
field-based interference according to IEC 61000-4-3	10 V/m
electrostatic discharge according to IEC 61000-4-2	8 kV air discharge
conducted HF interference emissions according to	Class A for industrial environment
design of the switching contact	Hybrid
minimum load [%]	50 %; from smallest adjustable rated current
operating frequency 1 rated value	50 Hz
operating frequency 2 rated value	60 Hz
relative positive tolerance of the operating frequency	5%
relative negative tolerance of the operating frequency	5%
ampacity when starting maximum	120 A
number of digital inputs	4
note	4 via 3DI/LC module
minimum permissible	20.4 V
maximum permissible	28.8 V
ON-delay time	20 ms
OFF-delay time	35 ... 50 ms
mounting position	Vertical, horizontal (observe derating)
fastening method	pluggable in BaseUnit
height	142 mm
width	30 mm
depth	150 mm
upwards	50 mm
downwards	50 mm
60721	not get into the devices)
relative humidity during operation	10 ... 95 %
air pressure according to SN 31205	900 ... 1 060 hPa
product function bus communication	Yes
supports PROFIenergy measured values	Yes
supports PROFIenergy shutdown	Yes
1 for digital input signals	Pluggable module - accessory
for main energy infeed	Plug contact to Base Unit
for load-side outgoing feeder	Plug contact to Base Unit
wire length for motor unshielded maximum	200 m
other	Dangerous goods
Environment	Industrial Communication
last modified:	4/4/2026

Ficha técnica oficial del fabricante con todas las especificaciones.

Producto bajo pedido

Puedes pedirlo ya: te lo servimos en el plazo indicado. Selecciona la cantidad para añadirlo al carrito.

Plazo de entrega (días):

Avísame cuando haya stock

Si prefieres esperar a que vuelva a haber envío inmediato, déjanos tu email.

Solo usaremos tu email para avisarte de este artículo.

ET 200SP, arrancador inversor 4,0-12A HF

3RK1308-0BE00-0CP0

€655,49 EUR

3RK1308-0BE00-0CP0

Plazo de entrega (días):

€655,49 EUR /cada

Plazo de entrega (días):

€655,49 EUR /cada

Total:

Total: €0,00 EUR

en el carrito Total: