€1.598,03 EUR
+ VAT
Especificaciones técnicas
Protección y seguridad
| Reverse polarity protection | Yes |
|---|---|
| short-circuit | Yes |
| Isolation tested with | 750 V DC (type test) and according to EN 50155 (routine test) |
| Performance level according to ISO 13849-1 | Cat. 4, PLe |
| SIL acc. to IEC 61508 | SIL 3 |
| Fire protection acc. to EN 45545-2 | Yes; For proof of conformity, see Service & Support |
| Protection against fouling acc. to EN 60664-3 | Yes; Type 1 protection |
Seguridad funcional
| low demand mode: PFDavg in accordance with SIL1 | < 2.00E-03 signal monitoring disabled |
|---|---|
| high demand/continuous mode: PFH in accordance | < 3.00E-08 1/h signal monitoring disabled |
| High demand/continuous mode: PFH in accordance | < 1.00E-09 1/h |
Datos eléctricos
| Current consumption, max. | 50 mA; without load, 150 mA with 300 mA encoder load |
|---|---|
| Output current, max. | 300 mA |
| Power loss, typ. | 1.25 W |
| Type of input voltage | sin/cos 1 Vpp |
| Input voltage | 1 Vpp, centered at 2.5 V offset |
| Monitoring the supply voltage | Yes |
| Monitoring of the supply voltage (PWR-LED) | Yes; green LED |
Entradas/Salidas y comunicación
| Number of RS 485 interfaces | 0 |
|---|
Detección y sensórica
| Counter for incremental encoder | Yes |
|---|---|
| Incremental encoder (symmetrical) | Yes; up to 200 kHz depending on cable type and length |
| Incremental encoder with A/B tracks, 90° phase offset | Yes; sin/cos |
| A/B transition error at incremental encoder | Yes |
Conexión y cableado
| Cable length, shielded, max. | 150 m |
|---|
Montaje y material
| Color code for module-specific color-coded label | CC01 |
|---|
Condiciones ambientales
| Installation altitude above sea level, max. | 2 000 m |
|---|---|
| Ambient air temperature-barometric pressure-altitude | Tmin ... Tmax at 1 140 hPa ... 795 hPa (-1 000 m ... +2 000 m) |
Otras características
| Product type designation | F-TM Count 1x1Vpp sin/cos HF |
|---|---|
| FW update possible | Yes |
| based on | 6ES7136-6CB00-0CA0 |
| usable BaseUnits | BU type A0 |
| I&M data | Yes; I&M0 to I&M3 |
| STEP 7 TIA Portal configurable/integrated from version | see entry ID: 109746275 |
| Rated value (DC) | 24 V |
| permissible range, lower limit (DC) | 20.4 V |
| permissible range, upper limit (DC) | 28.8 V |
| Inputs | 14 byte; S7-300/400F CPU, 13 byte |
| Outputs | 5 byte; S7-300/400F CPU, 4 byte |
| Automatic encoding | Yes |
| Electronic coding element type H | Yes |
| Number of digital inputs | 1; (counter input) |
| Digital inputs, parameterizable | Yes |
| Gate start/stop | Yes |
| Number, max. | 1 |
| Minimum pulse width for program reactions | 2.5 µs |
| parameterizable | Yes |
| shielded, max. | 150 m |
| Input frequency, max. | 200 kHz |
| Counting frequency, max. | 800 kHz; with quadruple evaluation |
| Diagnostics function | Yes; see chapter "Diagnostic Messages" in the manual |
| Diagnostic alarm | Yes |
| Wire break | Yes |
| RUN LED | Yes; green LED |
| ERROR LED | Yes; red LED |
| Channel status display | Yes; green LED |
| for channel diagnostics | Yes; red LED |
| for module diagnostics | Yes; green/red DIAG LED |
| Counter | Yes |
| Number of counters | 1 |
| Safe Operating Stop (SOS) | Yes |
| Safely-Limited Speed (SLS) | Yes |
| Safe Direction (SDI) | Yes |
| Safe Speed Monitor (SSM) | Yes |
| Continuous counting | Yes |
| Counter response parameterizable | Yes |
| Software gate | Yes |
| Counting range, parameterizable | Yes |
| Frequency measurement, min. | 0.04 Hz |
| Frequency measurement, max. | 800 kHz; with quadruple evaluation |
| Cycle duration measurement, min. | 1 µs |
| Cycle duration measurement, max. | 25 s |
| Velocity measurement, min. | 0 (speed in configured units per selected time basis - speed*1 000) |
| between the channels | No; Only one channel is available |
| between the channels and backplane bus | Yes |
| Suitable for safety functions | Yes |
| 50716 | specific application under consideration of all local regulations. |
| Low demand mode: PFDavg in accordance with | < 3.00E-05 |
| EN 50121-3-2 | Yes; EMC for rail vehicles |
| EN 50121-4 | Yes; EMC for signal and telecommunications systems |
| EN 50121-5 | Yes; EMC for fixed installations and railway power supply equipment |
| EN 50125-1 | Yes; Rail vehicles - see ambient conditions |
| EN 50125-2 | Yes; Stationary electrical equipment - see ambient conditions |
| EN 50125-3 | Yes; Signal and telecommunications systems - see ambient conditions; |
| EN 61373 | Yes; Rail vehicles - vibrations and shocks: Category 1 Class A/B |
| horizontal installation, min. | -25 °C; = Tmin (incl. condensation/frost) |
| vertical installation, min. | -25 °C; = Tmin |
| vertical installation, max. | 55 °C; = Tmax |
| 2-38, max. | horizontal installation |
| Resistant to commercially available coolants and | Yes; Incl. diesel and oil droplets in the air |
| 60721-3-3 | Class 3B3 on request |
| to EN 60721-3-3 | 0AA0//6AG1193-6AB00-0AA0) |
| 60721-3-5 | Class 5B3 on request |
| to EN 60721-3-5 | 0AA0/6AG1193-6AB00-0AA0) |
| agriculture acc. to ISO 15003 | (6AG1193-6AA00-0AA0/6AG1193-6AB00-0AA0) |
| conditions acc. to EN 60721, EN 60654-4 and | during operation! |
| Electronic equipment on rolling stock acc. to EN 50155 | Yes; class PC2 protective coating acc. to EN 50155 |
| Military testing according to MIL-I-46058C, Amendment 7 | Yes; Discoloration of coating possible during service life |
| Qualification and Performance of Electrical Insulating | Yes; Conformal coating, Class A |
| Width | 15 mm |
| Height | 73 mm |
| Depth | 58 mm |
| Weight, approx. | 42 g |
| Functional Saftey | Railway |
| TUEV | TUEV |
| last modified: | 7/3/2026 |
Accesorios
-