ET 200SP, D-O-L starter F 0.1-0.4A HF
Siemens

ET 200SP, D-O-L starter F 0.1-0.4A HF

Arrancador directo de seguridad High Feature; maniobra electrónica; protección electrónica contra sobrecarga hasta 0,09 kW/400 V; rango de ajuste 0,1...0,4 A; PROFIenergy; opción: módulo 3DI/LC

🔌 ComunicaciónYes
Protección y seguridad
performance level (PL) according to ISO 13849-1PL e
category according to ISO 13849-14
device type according to ISO 13849-11
Safety Integrity Level (SIL) according to IEC 61508SIL 3
safety device type according to IEC 61508-2Type B
PFH according to IEC 61508 relating to SIL6E-9 1/h; for switching frequency 30/h
PFDavg with low demand rate according to IEC 615089E-7; for switching frequency 30/h
hardware fault tolerance according to IEC 615081
of service life according to IEC 6150820 a
Safety Integrity Level (SIL) according to IEC 61508 relatingSIL 1
hardware fault tolerance according to IEC 61508 relating to1
Entradas/Salidas y comunicación
PROFIBUS DP protocolYes
PROFINET protocolYes
type of electrical connection of the communication interfacePlug contact to Base Unit
Condiciones ambientales
installation altitude at height above sea level maximum4 000 m
Prestaciones y durabilidad
B10 value with high demand rate according to SN 319201 000 000
Otras características
product brand nameSIMATIC
product categoryMotor starter
product type designationET 200SP
equipment version according to IEC 60947-4-23
product functionFail-safe direct-on-line starter
on-site operationYes
intrinsic device protectionYes
remote firmware updateYes
for power supply reverse polarity protectionYes
at AC in hot operating state per pole0W
insulation voltage rated value500 V
degree of pollution2
overvoltage categoryIII
surge voltage resistance rated value6 kV
between main and auxiliary circuit500 V
consumed current maximum140 mA
shock resistance6 g / 11 ms
vibration resistance15 mm to 6 Hz; 2 g to 500 Hz
operating frequency maximum1 1/s
type of coordination1
according to IEC 60947-4-2AC-53a: 0,4 A: (8-0,7: 70-32)
Net Weight0.421 kg
direct startYes
product function short circuit protectionYes
design of short-circuit protectionfuse
at 400 V rated value55 kA
at 500 V rated value55 kA
at 500 V according to UL 60947 rated value100 kA
EMC emitted interference according to IEC 60947-1class A
EMC immunity according to IEC 60947-1Class A
due to burst according to IEC 61000-4-43 kV
due to conductor-earth surge according to IEC 61000-4-54 kV
due to conductor-conductor surge according to IEC2 kV
due to high-frequency radiation according to IEC 61000Class A
field-based interference according to IEC 61000-4-320 V/m
electrostatic discharge according to IEC 61000-4-28 kV air discharge
conducted HF interference emissions according toClass A for industrial environment
product function suitable for safety functionYes
safety-related switching OFFYes
safe stateLoad circuit open
test wear-related service life necessaryYes
function test interval maximum0.083 a
stop category according to IEC 60204-10
proportion of dangerous failures with high demand rate50 %
Safety Integrity Level (SIL) according to IEC 62061SIL 3
Safe failure fraction (SFF)99.5 %
touch protection against electrical shockfinger-safe
protection class IP on the front according to IEC 60529IP20
touch protection on the front according to IEC 60529finger-safe
number of poles for main current circuit3
design of the switching contactHybrid
minimum load [%]50 %; from smallest adjustable rated current
type of the motor protectionsolid-state
operating voltage rated value48 ... 500 V
relative symmetrical tolerance of the operating voltage10 %
operating frequency 1 rated value50 Hz
operating frequency 2 rated value60 Hz
relative positive tolerance of the operating frequency5%
relative negative tolerance of the operating frequency5%
operational current at AC at 400 V rated value0.4 A
ampacity when starting maximum4A
operating power for 3-phase motors at 400 V at 50 Hz0.06 ... 0.12 kW
number of digital inputs5
note4 via 3DI/LC module
safety-related1
type of input characteristicType 1 in accordance with EN 61131-2
input voltage at digital input at DC rated value24 V
input current at digital input for signal <1> typical0A
of the inputs4 byte
of the outputs2 byte
type of voltage of the supply voltageDC
minimum permissible20.4 V
maximum permissible28.8 V
supply voltage at DC rated value24 V
in standby mode of operation50 mA
during operation50 mA
at switching on of motor140 mA
in switching state OFF with bypass circuit1.2 W
in switching state ON with bypass circuit3.4 W
inrush current peak at 24 V25 A; Observe the manual for group configuration
duration of inrush current peak at 24 V0.14 ms
ON-delay time35 ms
OFF-delay time35 ... 50 ms
when switched off via control inputs maximum55 ms
when switched off via supply voltage maximum120 ms
at 40 °C rated value0.4 A
at 50 °C rated value0.4 A
at 55 °C rated value0.4 A
at 60 °C rated value0.4 A
mounting positionVertical, horizontal (observe derating)
fastening methodpluggable in BaseUnit
height142 mm
width30 mm
depth150 mm
upwards50 mm
downwards50 mm
during storage-40 ... +70 °C
during transport-40 ... +70 °C
60721not get into the devices)
relative humidity during operation10 ... 95 %
air pressure according to SN 31205900 ... 1 060 hPa
product function bus communicationYes
supports PROFIenergy measured valuesYes
supports PROFIenergy shutdownYes
1 for digital input signalsPluggable module - accessory
2 for digital input signalsPlug contact to Base Unit
for main energy infeedPlug contact to Base Unit
for load-side outgoing feederPlug contact to Base Unit
for supply voltage line-sidePlug contact to Base Unit
wire length for motor unshielded maximum200 m
tificateates/Test Report
Dangerous goodsEnvironment
last modified:4/30/2026
⬇ Descargar datasheet (PDF)

Ficha técnica oficial del fabricante con todas las especificaciones.

Material con posibilidad de devolución
ET 200SP, D-O-L starter F 0.1-0.4A HF
€423,38 EUR
€498,09 EUR
3RK1308-0CA00-0CP0
Plazo de entrega (días):
€423,38 EUR /each
Total:

Accesorios